Plumbing for Beginners: The Essentials for Installing a Bathtub

Plumbing for Beginners: The Essentials for Installing a Bathtub

Blog Article

Give Me A Quote!

How do you really feel about A Step-by-Step Guide to Installing a Bathtub?

A Step-by-Step Guide to Installing a Bathtub
Installing a tub isn't specifically brain surgery, but it does call for solid plumbing, carpentry, as well as occasionally, tiling skills. Changing an old bath tub with a new one is additionally a reasonably tough job. If the old tub is readily obtainable, the task can relocate quickly; if you need to open up a wall surface to eliminate the old tub as well as position the new tub, the task is much harder. In either instance, the task is within a home handyman's abilities, although you will certainly require a helper to move out the old bathtub and embeded in the brand-new one. Ensure you have qualified on your own for the job and fit trying it. As opposed to employing a professional to take over a halfway-completed task, it is better to take into consideration using one prior to you begin. Opportunities are you might need an expert plumber to make tube links.
This article will certainly assist you mount a new bathtub in your washroom if you have actually currently gotten a brand-new bathtub as well as don't need to change the arrangement of your previous water supply pipelines.
Your devices as well as product list should consist of the following:
  • New Bath tub

  • Hammer

  • Pipeline Wrenches

  • Prybar

  • Safety Glasses

  • Degree

  • Pliers

  • Adjustable Wrench

  • Putty Blade

  • Screwdriver

  • Cold Chisel

  • Tape Measure

  • Pipe Caps

  • Removing Old Taps

    If you require to replace old faucets with brand-new ones as a part of your installation, after that the first thing you must do is detach the water system. After doing so, turn on the taps to drain any kind of water staying in the system. The process of eliminating the existing faucets can be quite bothersome because of the restricted access that is often the case.
    Utilize a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that connects the supply pipes to the faucets. Have a towel all set for the remaining water that will come from the pipelines. When the supply pipes have been gotten rid of, make use of the same tool to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to quit the single taps from turning during this procedure. Once the faucets have been gotten rid of, the holes in the bath/basin will certainly need to be cleaned of any old securing substance.
    Before carrying on to fit the new faucets, compare the pipeline links on the old taps to the new faucets. If the old faucets are longer than the brand-new taps, after that a shank adapter is required for the brand-new faucets to fit.

    Fitting New Taps

    If the tails of the new faucets are plastic, then you will require a plastic port to avoid damages to the string. One end of the connector fits on the plastic tail of the tap as well as the various other end gives a link to the existing supply pipes.
    If you require to fit a monobloc, after that you will call for decreasing couplers, which connects the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
    Next, place the faucet in the mounting hole in the bath/basin making sure that the washing machines are in area in between the tap as well as the sink. Safeguard the faucet in position with the manufacturer given backnut. Once the faucet is safely in position, the supply pipelines can be connected to the tails of the faucets. The faucets can either be linked by utilizing corrugated copper piping or with typical faucet connectors. The former type should be linked to the tap finishes first, tightening up only by hand. The supply pipelines can later be linked to the various other end. Tighten up both ends with a spanner after both ends have been linked.

    Mounting the Bathtub

    Using both wood boards under its feet, position the tub in the called for placement. The wooden boards are helpful in equally spreading out the weight of the bathtub over the location of the boards as opposed to concentrating all the weight onto 4 small points.
    The following objective is to make sure that the bath tub is leveled all round. This can be achieved by examining the level and readjusting the feet on the bath tub till the spirit level reads level.
    To install faucets, fit the bottom of the furthest adaptable faucet connector to the appropriate supply pipe by making a compression join; after that do the very same for the other faucet.
    Switch on the water system and also inspect all joints and new pipework for leakages as well as tighten them if necessary. Load the bathtub and also check the overflow outlet as well as the typical outlet for leakages.
    Lastly, take care of the bathroom paneling as described in the manufacturer's instruction manual. Tiling and sealing around the bathtub must wait up until the bathtub has actually been utilized a minimum of once as this will certainly settle it into its last setting.

    Getting ready for the Installment

    First of all, the supporting structure provided with the bath should be fitted (if called for) according to the supplier's instructions. Next off, fit the taps or mixer to the bath tub. When suitable the tap block, it is very important to ensure that if the faucet features a plastic washer, it is fitted in between the bathroom and also the faucets. On a plastic bath, it is also reasonable to fit a sustaining plate under the faucets unit to stop stress on the bathtub.
    Fit the adaptable tap ports to the bottom of the two taps utilizing 2 nuts and olives (in some cases supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the electrical outlet with the hole in the bathroom. Make use of the nut provided by the producer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipe.
    Next, fit the end of the versatile overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bath. Make certain you utilize all of the provided washing machines.
    Attach the catch to the bottom of the waste outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Link all-time low of the overflow tube in a comparable manner.The bath need to now be ready to be fitted in its last position.

    Tiling Around the Tub

    In the area where the bath meets the ceramic tile, it is necessary to secure the accompanies a silicone rubber caulking. This is necessary as the installation can move sufficient to split an inflexible seal, triggering the water to penetrate the wall surface between the bathroom and also the tiling, resulting in issues with dampness and possible leakages to the ceiling listed below.
    You can pick from a selection of coloured sealers to blend in your fixtures as well as fittings. They are offered in tubes as well as cartridges, and also are capable of securing spaces up to a width of 3mm (1/8 inch). If you have a larger void to fill, you can fill it with twists of drenched paper or soft rope. Keep in mind to always fill up the bathtub with water before sealing, to enable the activity experienced when the bathtub is in usage. The sealant can fracture rather early if you do not take into consideration this motion before sealing.
    Additionally, ceramic coving or quadrant floor tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are also quickly offered on the market. It is a good idea to fit the tiles making use of waterproof or waterproof sticky and cement.

    A Step-by-Step Guide to Installing a Bathtub

    Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

    But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

    This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

    Remove the Existing Bathtub

    To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

    The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

    Choose the Right Bathtub

    The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

    Install the Plumbing and Ledger Board

    You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

    Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

    Install the Bathtub

    When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

    Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

    If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

    Hook up the Plumbing

    Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

    Install the Bathtub Surround

    A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

    Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

    If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

    If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

    Tools You Need to Install a New Bathtub

    Do you like reading about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround? Place a comment below. We'd be glad to know your feelings about this content. We hope that you visit us again before long. Sharing is caring. You never know, you could be doing someone a favor. Thanks a lot for your time. Visit us again soon.

    Plumbing excellence awaits.

    Report this page